GT 2125 GC 2125 GC 2125C Oper ator ′ s manual Please read the oper ator’s manual carefully and make sure you understand the instructions before usi
10 – EnglishGENERAL SAFETY PRECAUTIONSGeneral rulesOnly use cutting attachments with the guards we recommend! See the chapter on Technical data.Keep t
English – 11ASSEMBLYFitting the loop handle(GT 2125)• Position the handle on the shaft. Note that the handle must be mounted below the arrow on the sh
12 – EnglishASSEMBLYAssembling and dismantling the two-piece shaft(GC 2125C)Assembly:• Loosen the coupling by turning the knob.• Align the tab of the
English – 13ASSEMBLY• Insert a finger into the centre hole of the cover (I) while grasping the cover with your other fingers. Using the index finger and
14 – EnglishASSEMBLYFitting the trimmer guard and trimmer head(GT 2125)Guard• Fit the guard as shown in the diagram. Tighten securely.Trimmer head• Fi
English – 15FUEL HANDLINGFuel safetyNever start the machine:1 If you have spilt fuel on it. Wipe off the spillage and allow remaining fuel to evaporat
16 – EnglishFUEL HANDLINGMixing• Always mix the petrol and oil in a clean container intended for fuel.• Always start by filling half the amount of the
English – 17STARTING AND STOPPINGCheck before starting• Check the blade to ensure that no cracks have formed at the bottom of the teeth or by the cent
18 – EnglishSTARTING AND STOPPINGCAUTION! Do not pull the starter cord all the way out and do not let go of the starter handle when the cord is fully
English – 19WORKING TECHNIQUESGeneral working instructionsBasic safety rules1 Look around you:• To ensure that people, animals or other things cannot
2 – English KEY T O SYMBOLS Symbols W ARNING! Clearing saws, brushcutters and trimmers can be dangerous! Careless or incorrect use can result in s
20 – EnglishWORKING TECHNIQUESGrass clearing using a grass blade• Grass blades and grass cutters must not be used on woody stems.• A grass blade is us
English – 21WORKING TECHNIQUESSweeping• The fan effect of the rotating cord can be used for quick and easy clearing up. Hold the cord parallel to and
22 – EnglishMAINTENANCECarburettorYour Jonsered product has been designed and manufactured to specifications that reduce harmful exhaust fumes. The eng
English – 23MAINTENANCEFine adjustment of the idle speed TAdjust the idle speed using the idle adjustment screw T, if it is necessary to readjust. Fir
24 – EnglishMAINTENANCECooling systemTo keep the working temperature as low as possible the machine is equipped with a cooling system.The cooling syst
English – 25MAINTENANCETwo-piece shaft (GC 2125C)The drive shaft end in the lower shaft should be lubricated with grease every 30 hours. There is a ri
26 – EnglishMAINTENANCEMaintenance scheduleThe following is a list of the maintenance that must be performed on the machine. Most of the items are des
English – 27TECHNICAL DATATechnical dataNote 1: Noise emissions in the environment measured as sound power (LWA) in conformity with EC directive 2000/
28 – EnglishTECHNICAL DATAThe following attachments are recommended for the specified models.The following attachments have been developed mainly for t
English – 29TECHNICAL DATAEC-declaration of conformity(Applies to Europe only)Jonsered, SE-561 82 Huskvarna, Sweden, tel: +46 36-146500, declares unde
English – 3 CONTENTS Contents Note the f ollowing before starting: Please read the oper ator’s manual carefully. KEY TO SYMBOLS Symbols ...
"Clic"12356796,0 m18'483,05 m9'2,0-2,4 mm.079-.095"10 cm 4"6"15 cmTap-N-Go 25
1Trimmy H II234567897,5 m 25'2,0-2,4 mm.080-.095"12 15 cm 6"~ 3,7 m 12' 15 cm 6"
"Clic"12356710118,5 m28'484,2 m14'2,4-2,7 mm.095-.106"10 cm 4"6"15 cmS35
12432,4-2,7 mm.095-.106"4,25 m14'4,25 m14'B6"15 cmA6"15 cmS355
´®z+R;,¶6W¨´®z+R;,¶6W¨Tap-N-Go 35"Clic"12356798,5 m28'484,3 m14'2,4-2,7 mm.095-.106"10 cm 4"6"15 cm
1Auto 3223456789104,0 m 13'2,4 mm.095"~2,0 m6,5'6"6"15 cm15 cm
´®z+R;,¶6W¨2007-01-25´®z+R;,¶6W¨1150271-26
4 – English INTR ODUCTION Dear Customer , Cong ratulations on your choice to buy a Jonsered product!We are convinced that you will appreciate with
English – 5 WHA T IS WHA T? What is what?3130GC2125C 1 Trimmer head2 Grease filler cap, bevel gear3 Bevel gear4 Cutting attachment guard5 Shaft6 Lo
6 – English GENERAL SAFETY PRECA UTIONS Impor tant Personal protective equipment HELMET A protectiv e helmet where there is a risk of falling objec
English – 7 GENERAL SAFETY PRECA UTIONS CLO THINGWear clothes made of a strong fabric and avoid loose clothing that can catch on twigs and branches
8 – EnglishGENERAL SAFETY PRECAUTIONSCutting attachment guardThis guard is intended to prevent loose objects from being thrown towards the operator. T
English – 9GENERAL SAFETY PRECAUTIONSIf the muffler on your machine is fitted with a spark arrestor mesh this must be cleaned regularly. A blocked mesh
Commentaires sur ces manuels